Savi Sol Specifikace stáhnout pdf (Strana 8)

9400 SOUTHRIDGE PARK COURT, SUITE 200, ORLANDO, FL 32819 USA

TEL: 407.855.5630 FAX: 407.210.8679 nextstepproduct.com

BASIC TROUBLESHOOTING GUIDE - FOR ADDITIONAL INFORMATION CONTACT

TECHNICAL SERVICES AT TELEPHONE NUMBERS LISTED BELOW

ALL LIGHTS FAIL TO ILLUMINATE - Check 120V power supply into transformer - Check for 12V

output at transformer - check or reset GFCI. Make sure 120 volts has not been used in the

installation of these lights - damage is assured and is NON WARRANTY.

ONE OR MORE LIGHTS DIM - This is generally caused by a poor connection or improper wire

gauge. To determine if light or lights has fault - separate each light from all other lights and

independently wire 12V to this light only. Repeat process on each light. If junction box is used -

recheck for proper connection of light cord. AGAIN IF A JUNCTION BOX IS BEING USED - VERIFY

THAT THE CORRECT WIRE GAUGE IS BEING USED BETWEEN TRANSFORMER AND JUNCTION BOX.

EVEN THOUGH OTHER LIGHTS MIGHT WORK CORRECTLY - IMPROPER WIRE GAUGE SIZE COULD

ALLOW 1 OR MORE LIGHTS TO WORK IMPROPERLY. Measure and verify that proper low voltage is

being supplied to lights - see WIRE GAUGE & WIRE LENGTH GUIDE CHART.

BLINKING, FLASHING, NON WORKING LIGHTS - This is generally caused by a poor connection

or improper wire gauge. To determine if light or lights has fault - separate light from all other lights

and independently wire 12V to this light only. Repeat process on each light. If junction

box is used - recheck for proper connection of light cord. AGAIN IF A JUNCTION BOX IS BEING

USED - VERIFY THAT THE CORRECT WIRE GAUGE IS BEING USED BETWEEN TRANSFORMER

AND JUNCTION BOX. EVEN THOUGH OTHER LIGHTS MIGHT WORK CORRECTLY - IMPROPER

WIRE GAUGE SIZE COULD ALLOW 1 OR MORE LIGHTS TO WORK IMPROPERLY. Measure and

verify that proper low voltage is being supplied to lights - see WIRE GAUGE & WIRE LENGTH

GUIDE CHART. MOST IMPORTANTLY SEE CHART FOR MIN/MAX VOLTAGE & CORD

LENGTH CHART.

2013/14 SAVI LED LIGHTING PRODUCTS

COLORED LIGHTS OUT OF SYNCH - Follow Synchronization Instructions in this Guide. Be very

patient and read instruction carefully. If lights fail to synchronize - verify that proper wire

connections are being achieved for those lights that are out of step with others. Generally a lights

failure to sync with the rest is: improper voltage supply or poor connection to light.

NOTE: In most situations problems come down to 4 main faults: improper voltage supply,

improper wiring gauge,improper/poor wiring connections or the light itself.

2013/14 SAVI LED LIGHTS ARE FIELD SERVICABLE AND THE CORD AND LIGHT BODY

FIXTURE SHOULD NOT BE REMOVED COMPETELY FROM THE CONDUIT OR POOL. THERE SHOULD

BE ENOUGH CORD SUPPLIED IN THE SERVICE LOOP TO REMOVE LIGHT FROM WALL FITTING AND

LIFTED ABOVE WATER LEVEL FOR LED LIGHT CARTRIDGE REPLACEMENT. IF THERE IS NOT

ENOUGH CORD IN SERVICE LOOP OR IT CANNOT BE ACCESSED - POOL WATER CAN BE DRAINED

BELOW LIGHT TO ACCESS FRONT OF LIGHT.

DO NOT PULL LIGHT AND CORD ENTIRELY FROM CONDUIT UNLESS INSTRUCTED BY COMPANY.

SAVI POOL AND SPA WILL NOT ACCEPT ENTIRE LIGHTS BEING RETURNED FOR SERVICE

UNLESS INSTRUCTED BY COMPANIES TECHNICAL SERVICES DEPARTMENT

ONLY LED LIGHT CARTRIDGES SHOULD BE REPLACED OR EXCHANGED WITH THE

2013/14 PRODUCT

Refer to the Light Cartridge Replacement Instructions included in this Guide for light replacement.

WARNING: All servicing of SAVI LED Lights should be done by a licensed or certified electrican or

a qualified pool professional in accordance with the National Electric Code (NEC) or Canadian

Electric Code (CEC)

For additional troubleshooting assistance or installation advice please contact Technical

Services at telephone number below.

1 2 3 4 5 6 7 8 9 10

Komentáře k této Příručce

Žádné komentáře

Savi Sol Specifikace Strana 8

Komentáře k této Příručce